Take a look at our past work!

Sectional Repair

Sold by Jaiyro

Conejo Valley Home Services will perform a sectional drain line repair under the upstairs master bathroom lavatory sink. The affected section is approximately 4 feet within the wall, accessible from beneath the vanity.

Work will entail cutting drywall as necessary behind and under the vanity to access the damaged pipe section. Once exposed, we will cut out the corroded section of cast iron drain located beneath the second elbow and replace it with new PVC material up to current code standards. The new section will extend all the way back to the existing trap arm connection.

In addition, Upon completion of installation, we will run a camera inspection to verify the integrity and successful restoration of drainage.

Total Estimate: $2207.00

(Includes 20% member discount applied)

Warranty:

This repair includes a 3-year parts and labor warranty covering workmanship and installed materials.

Disclaimer:

Conejo Valley Home Services is not responsible for the repair or replacement of drywall, tile, paint, cabinetry, or other finishes that may require removal to complete this scope of work. Any such repairs are to be handled by others upon completion of plumbing work.

Amount to collect when done: $2,207.00Please call Thomas 408-421-1557

Install a TOTO promenade2 1 piece toilet in Upstairs Master bathroom.

Per Andrew.

[Toilet is in shop]

Amount to collect when done $1,189.00 [check/cc]

Please call Bob (805) 794-0502

Sales- TonyPLease send Krista a picture of the water heater label

50-Gallon Gas Water Heater Replacement

Replacement of an existing 50-gallon gas water heater in a garage with no recirculation pump.

Location: Garage

Recirculation Pump: No

Tasks:

Preparation and Shutoff:

1. Shut off gas supply valve

2. Close main water supply

3. Drain existing water heater to empty tank

Removal of Existing Unit:

1. Disconnect gas line from heater

2. Detach cold and hot water supply lines

3. Remove and dispose of old unit per local regulations

New Water Heater Installation:

1. Position new 50-gallon unit with adequate clearance per code

2. Install new drain pan beneath unit

3. Connect new stainless steel water supply lines (cold and hot)

4. Install 1/4-turn ball valve on cold water inlet

5. Install expansion tank, adjusted to home water pressure (typically 50-60 PSI)

6. Fit new gas shutoff valve on gas line

7. Attach new flexible gas supply line with sediment trap

8. Secure unit with Unistrut mounting and earthquake straps

9. Reconnect to existing T&P relief valve exit point

10. Insulate water supply lines for efficiency

11. Install copper bonding wire from water lines to gas line for grounding

12. Cover base/stand with sheet metal for protection

Venting and Combustion:

1. Install venting per manufacturer's specs (e.g., double-wall or single-wall as required)

2. Secure single-wall vent connections with 3 screws each

3. Verify adequate combustion air supply per code

Testing and Startup:

1. Pressure-test gas and water connections for leaks

2. Fill tank and purge air from lines

3. Test T&P relief valve operation

4. Light pilot, set temperature to 120°F (or per client preference), and confirm burner ignition

5. Validate full operational status

Cleanup and Final Steps:

1. Clear debris from work area

2. Haul away old unit for disposal

3. Conduct final inspection with client walkthrough

Notes:

- Estimate valid for 60 days from issuance

- Includes permit fees (if required)

- Unforeseen issues or additional work will be quoted separately with client approval

- Exclusions: Drywall, paint, stucco, tile, concrete, stone repairs, or existing water damage

- Duration: 3-4 hours, 1 technician

- Warranty: Manufacturer - 6 years parts, 1 year labor; Conejo - 3 years labor

- Financing: 18 months at 0% interest available

- Qualifies for applicable utility rebates and federal tax credits (where available)

Gas repair will be done live

Remove 1-1/2 plug on gas elbow.

Install small nipple

Install 1-1/2 ball valve on elbow

Check for leaks.

Customer made us aware of his water heater that has a issue relighting which is why are doing the repair live.

No responsible for water heater

One year warranty on valve installed CC or check $3485.00

Sales- DerekPLEASE CALL WHEN HEADED OUT TO LOCATION!!

Through wall with repair plate.

Single Handle Tub/Shower Valve

Installation of a new single-handle tub/shower valve to provide reliable temperature and flow control.

Location: Tub/Shower

Tasks:

Preparation:

1. Shut off water supply to tub/shower (valve or main line).

2. Remove old valve, handle, and trim plate via access panel or wall.

3. Set up work area with drop cloth and tools (wrench, pipe cutter).

Valve Installation:

1. Install new single-handle valve body (copper or PEX connections).

2. Solder or crimp fittings to existing hot/cold lines per code.

3. Mount valve securely and attach trim plate, handle, and diverter.

Testing:

1. Turn on water supply and check for leaks at connections.

2. Test valve for hot/cold mixing, flow, and diverter function.

3. Adjust pressure balance or scald guard if applicable.

Cleanup and Final Steps:

1. Wipe down tub/shower area to remove debris.

2. Dispose of old valve per local regulations.

3. Conduct client walkthrough to demonstrate operation.

Notes:

- Includes standard pressure-balance valve; thermostatic models quoted separately.

- Wall access or tile repairs quoted separately if needed.

- Advise client to test valve periodically for smooth operation.

- Estimate valid for 60 days from issuance

- Includes permit fees (if required)

- Unforeseen issues or additional work will be quoted separately with client approval

- Exclusions: Drywall, paint, stucco, tile, concrete, stone repairs, or existing water damage

- Duration: 2-3 hours, 1 technician

- Warranty: 1 year parts and labor

- Financing: 18 months at 0% interest availableCC or Check $1100.00

Sales- Bryan Castaneda**Send Krista water heater label or upload to acct**Customer is fostering a dog in the garage. Possible sensitivity to loud sounds.

Install:Install tankless, prv , Roman tub valve and drain piece

2 techs 6 hours $0 to collect per return visit formNo Parts Needed

Installation **TWO DAY PROJECT; 3/23 + 3/24 ***MUST TARP EVERYTHING

Sales- Greg

Turn- William

U/S- 4TON horizontal furnace, coil, a/c, CleanEffects, ducting 7-8 runs, ECO-BEE, CleanEffectsD/S- 4TON horizontal furnace, coil, A/C, CleanEffects, ducting 7-8 runs, ECO-BEE, CleanEffectsTotal due - $54,000.00 (CHECK)

Install *ELECTRICAL PORTION, 11/3 + 11/4

Sales- Owen

26KW Generator

Total for this portion - $20,770.44 (CC OR CHECK)

Install *PLUMBING PORTION* 1-1/4 underground gas line approximately 25ft **INSTALL GAUGE, SEDIMENT TRAP, AND PUT GAS-LINE ON TEST*Sales- Owen26KW GeneratorRunning gas lines; **INSTALL GAUGE, SEDIMENT TRAP, AND PUT GAS-LINE ON TEST*Total for this portion - $2,500.00 *CC OR CHECK*

Installation **7AM PRE

Sales- Greg

Turn- JuanD/S - 4TON horiz S8V2 furnace/coil, BOVA20 A/C, Honeywell #T10 PRO, U/S - 4TON horiz S8V2 furnace/coil, BOVA20 A/C, Honeywell #T10 PRO (2) A/C surge protectors, Electrical run.Total due - $45,800.00 (NOTE: ACCT TO CALL 1/16 TO COLLECT $20,000.00 AT END OF DAY. THEN TO CALL MONDAY OR TUESDAY TO COLLECT REMAINING BALANCE)