Take a look at our past work!

Installation

Sales- Jesse

Turn- David

G5TON horizontal S8V2 furnace/coil, GOV60H2BA A/C, NUVE thermostat

Total for this portion - $18,300.00 (Office has CC)

Installation **TWO DAY PROJECT; 12/12 + 12/13 **IF CUSTOMER IS NOT HOME, SIDE DOOR TO GARAGE WILL BE UNLOCKED. IT IS OKAY TO OPEN MAIN GARAGE DOOR FROM INSIDE. IT IS ALSO OK TO GO THROUGH ATTIC IN MASTER BEDROOM CLOSET.

Sales- Jesse Cruz

Turn-

HVAC- 4TON Upflow SL280V furnace, coil, BOVB18 A/C, ducting, 10 runs, ECO-B, CleanEffects, iWaveINSULATION - 12/16 + 12/17: Remove approx 1,500 sq. ft. of BATT insulation. Perform air seal. Install approx 1,500 sq. ft. of blow-in insulation to R-38 value. PLUMB- Install new Flagship water filter (M# 1354)

Total due - $42,750.00 *Customer will be financing and paying with check*

Sales-TracyLead: Alexander Quiroz

**Send Krista water heater label or upload to acct**This proposal includes the following

Removal old existing 50 gallon and haul away

Install new ez98 with proper mounting

Install new expansion tank

Bonding wire

Sediment trap

Run proper venting for tankless exhaust

15 year heat exchanger warranty

5 year CONEJO workmanship warranty

Tank to tankless rebate form

Bulk discount if tankless water heater and filter system are installed together

-Water softner/ potassium tank Client is experiencing water spotting in dishes

This includes adding a second tank with a potassium holding tank

Includes proper drainage

And setting up filter

CC or Check $$11,563.00

Install

Sales- Greg Jamroz

Turn- N/A

Upflow furnace, coil, A/C

Total - $11,210.00 (CC)

Sales-Tony**Send Krista water heater label or upload to account**Call Tony for parts 50-Gallon Gas Water Heater Replacement

Replacement of an existing 50-gallon gas water heater in a garage with no recirculation pump.

Location: Garage

Recirculation Pump: No

Tasks:

Preparation and Shutoff:

1. Shut off gas supply valve

2. Close main water supply

3. Drain existing water heater to empty tank

Removal of Existing Unit:

1. Disconnect gas line from heater

2. Detach cold and hot water supply lines

3. Remove and dispose of old unit per local regulations

New Water Heater Installation:

1. Position new 50-gallon unit with adequate clearance per code

2. Install new drain pan beneath unit

3. Connect new stainless steel water supply lines (cold and hot)

4. Install 1/4-turn ball valve on cold water inlet

5. Install expansion tank, adjusted to home water pressure (typically 50-60 PSI)

6. Fit new gas shutoff valve on gas line

7. Attach new flexible gas supply line with sediment trap

8. Secure unit with Unistrut mounting and earthquake straps

9. Reconnect to existing T&P relief valve exit point

10. Insulate water supply lines for efficiency

11. Install copper bonding wire from water lines to gas line for grounding

Venting and Combustion:

1. Install venting per manufacturer's specs (e.g., double-wall or single-wall as required)

2. Secure single-wall vent connections with 3 screws each

3. Verify adequate combustion air supply per code

Testing and Startup:

1. Pressure-test gas and water connections for leaks

2. Fill tank and purge air from lines

3. Test T&P relief valve operation

4. Light pilot, set temperature to 120°F (or per client preference), and confirm burner ignition

5. Validate full operational status

Cleanup and Final Steps:

1. Clear debris from work area

2. Haul away old unit for disposal

3. Conduct final inspection with client walkthrough

Notes:

- Estimate valid for 30 days from issuance

- Permit fees, if required, are included as a separate line item

- Unforeseen issues or additional work will be quoted separately with client approval

- Exclusions: Drywall, paint, stucco, tile, concrete, stone repairs, or existing water damage

- Duration: 3-4 hours, 1 technician

- Warranty: Manufacturer - 10 years parts, 3 year labor.

- Qualifies for applicable utility rebates and federal tax credits (where available)

CC or Check $4489.00

Installation

Sales- Greg

Turn- Parker

DOWNSTAIRS SYSTEM- 5TON

BOVA15 A/C, horizontal coil, line set, duct mod, NUVE thermostat*NOTE: PAUL will be handling the UPSTAIRS system.

Total due - $22,750.00 *Synchrony 7.99*

Installation

Sales- Greg

Turn- ParkerU/S - 5TON Add on BOVA15 A/C, B6H96 furnace/coil (relocate to attic), duct mod, new Honeywell two-zone system, (2) NUVE thermostats, CleanEffects,

Total for this portion - $35,450.00 *Synchrony 7.99 and CC*

Installation **FRANCISCO; CALL MATT ONCE ONSITE REGARDING THE ELECTRICAL.

Sales- Greg

Turn- N/AD/S- 4TON horiz BGH96 furnace and CleanEffects

Total due - $15,500.00 *COLLECT CC*

1 of 2Sales: Derekremove the broken 3” abs cleanout tee and associated fittings. Wall is already open, Conejo does not patch or repair drywall.

Will relocate the 1-1/4” sprinkler valve near the ac condenser approximately 8’ towards the current condenser. Will include ne brass sprinkler valve.Collect: $2,400.00 / GC: #9317

Confirmed

Installation

Sales- Greg

Turn- Dakota

HVAC- 4TON Horiz R802VA furnace/coil, BOVA15 A/C, ducting 11 runs, Honeywell #T6

ELEC- Relocate light switch in the attic close to the existing attic access.

Total due - $23,030 (Luz to call for payment)