Take a look at our past work!

Install

Sales- Greg

100a - 200amp panel upgrade. Repace existing water bond with #4 copper. Add water heater bonding.

Total to collect - $9,500.00

Installation

Sales- Greg

Turn- DakotaHVAC- 3TON Upflow SL280V furnace, coil, BOVB18 A/C, ducting 4 runs (U/S), 4 registers (U/S), Honeywell #T6INSULATION- Installing approx. 750 sq. ft. of blown-in insulation to R38 value over existing.$21,250.00 (Financing; Wells Fargo 12 months)Balance due - $11,500.00 (VISA)

**Remaining $9,500.00 will be collected when the Panel Upgrade is scheduled (waiting for permit/Edison approval)

Install

Sales- Greg

Turn- Jesse Murillo 

Panel upgrade; 125a to 200a, + whole house surge protector.

Total due - $7,400.00 (VISA)

Sales: JohnReplacement of an existing 50-gallon gas water heater in a garage with no recirculation pump.

Location: closest

Recirculation Pump: No

Tasks:

Preparation and Shutoff:

1. Shut off gas supply valve

2. Close main water supply

3. Drain existing water heater to empty tank

Removal of Existing Unit:

1. Disconnect gas line from heater

2. Detach cold and hot water supply lines

3. Remove and dispose of old unit per local regulations

New Water Heater Installation:

1. Position new 50-gallon unit with adequate clearance per code

2. Install new drain pan beneath unit

3. Connect new stainless steel water supply lines (cold and hot)

4. Install 1/4-turn ball valve on cold water inlet

5. Install expansion tank, adjusted to home water pressure (typically 50-60 PSI)

6. Fit new gas shutoff valve on gas line

7. Attach new flexible gas supply line with sediment trap

8. Secure unit with Unistrut mounting and earthquake straps

9. Reconnect to existing T&P relief valve exit point

10. Insulate water supply lines for efficiency

11. Install copper bonding wire from water lines to gas line for grounding

12. Cover base/stand with sheet metal for protection

Venting and Combustion:

1. Install venting per manufacturer’s specs (e.g., double-wall or single-wall as required)

2. Secure single-wall vent connections with 3 screws each

3. Verify adequate combustion air supply per code

Testing and Startup:

1. Pressure-test gas and water connections for leaks

2. Fill tank and purge air from lines

3. Test T&P relief valve operation

4. Light pilot, set temperature to 120°F (or per client preference), and confirm burner ignition

5. Validate full operational status

Cleanup and Final Steps:

1. Clear debris from work area

2. Haul away old unit for disposal

3. Conduct final inspection with client walkthroughCollect: $3,385.00

Confirmed with Keith 805-795-1137 who will be on site 05/23, 11-1

Per Matt (Put this on install, Korey and Jesse)Sold by Alex

Replace 50amp Sylvania sub panel with 125 amp sub panel

Customer is H/O

Not Gated

Amount to collect: $2500

Please call when you're on the way (805) 728-5378 Laura

Install ***DAY 2 OF 2

Sales- Greg

Turn- Craig

Main House- Horizontal XV-80 furnace, coil, BOVB18 A/C

Bedrooms- Horizontal XV-80 furnace, coil, BOVB18 A/C, approx 9 runs.

Deposit - $1,000.00 (CC)

Total due - $36,000.00 (CC or check; homeowner to decide)

Sales- NickEstimate to reroute failed cold water line in slab through attic.

5 year warranty on material through Conejo

2 year warranty on material through Conejo

Conejo does not patch/repair stucco, drywall, texture, paint, flooring, carpet, tile, etc. if needed a referral to a licensed contractor can be provided.

Scope of work :

- set up plastic containment in areas where work will be preformed

- cut drywall open to expose manifolds

- shut water off to house

* turn power off to circulation pump in garage

- drain system down

- cut open manifold to confirm leaking line

- run fish tape to confirm end of line

- cap line off and turn water back on

- run new PEX line through attic

- strap PEX line along is pathway

- rebuild manifolds to abandon old line in slab and feed new line over head

- shut water off and drain system down

- switch system over

- allow PEX to rest prior to pressure test

- to water on and pressure test for leaks

- purge system of air

- double check meter to ensure there are no secondary leaks

- purge circulation system of air before turning power back on to pump

- clean up work area once job is complete Reroute material list :

House is very clean !!!

Start job with opening drywall underneath en-suite lavatory sink ( bed room where cats are at ) and preform drop down test after cutting open manifold. Make sure circulation pump to water heater in garage is turned off to avoid burning up pump. Fish tape line to confirm manifold. Picked up manifold in hallway near guest and in bedroom where incoming water to house is located.

2 techs

8 hours

Tools

- 6’ ladder

- hole hawg

- PEX gun

- vacuum

- drop cloths, runners, plastic

Material

- 75’ of 3/4” cold PEX

- PEX trays 1/2”, 3/4”, 1”

- Copper trays 1/2”, 3/4”, 1”

- bring a roll of 1” PEX just in caseCC or check-$4313.14

1" Cold Water Re-Route

Sold by Nick S.

After re-route of two lines there is still water loss in system during drop down test. Water main and 1” cold line in closet on en-suite bedroom is reading over 100 decibels with leak detection equipment.

Estimate to reroute failed cold water line in slab through attic.

5 year warranty on material through Conejo

2 year warranty on material through Conejo

Conejo does not patch/repair stucco, drywall, texture, paint, flooring, carpet, tile, etc. if needed a referral to a licensed contractor can be provided.

Scope of work :

- set up plastic containment in areas where work will be preformed

- cut drywall open to expose manifolds

- shut water off to house

* turn power off to circulation pump in garage

- drain system down

- cut open manifold to confirm leaking line

- run fish tape to confirm end of line

- cap line off and turn water back on

- run new PEX line through attic

- strap PEX line along is pathway

- rebuild manifolds to abandon old line in slab and feed new line over head

- shut water off and drain system down

- switch system over

- allow PEX to rest prior to pressure test

- to water on and pressure test for leaks

- purge system of air

- double check meter to ensure there are no secondary leaks

- purge circulation system of air before turning power back on to pump

- clean up work area once job is complete

Amount to collect when done: $1,984.00

Please call 8057285378

Sales-Tracy

This includes re routing hot water lines and cold water lines We will re route remaining cold water line for master bathroom, as well as hot water lines , we will re route garage hot and cold water lines from water heater , we will re route hot and cold water lines from other side water heater in closet , we will re route interior bathroom hot and cold water lines though attic , only water lines we will not touch at this time is the kitchen , this includes island sink , main kitchen sink and fridge water lines, this section of home will not be included due to the fact this a fairly new plumbing system , we can add isolation valves to these water lines for the future if they need to be fixed or re routed.Financing $15,343.00

InstallSales- OwenTurn-200amp to 200amp panel upgrade

Install

Sales- Owen

Turn- N/A

Upgrade 200amp panel to new 200amp panel

Total due- $5,800.00 (CC or check)