Take a look at our past work!

Installation

Sales- Jesse

Turn- Jesse Murillo

3TON upflow R801 furnace, NUVE thermostat *DO NOT TAKE OLD THERMOSTAT AWAY, LEAVE WITH CLIENT*DEPOSIT - $740.00 (CC)

TOTAL DUE - $6,660.00 (CC)

Installation

Sales- Greg

Turn- Jesse Murillo

5TON upflow GR9S80 furnace

Total due - $7,500.00 (CC)

Drain and remove existing water heater

Clean and prep area

Install grounding, and strapping

Sheet metal stand

Install new smitty pan

Install new 50 gal Bradford to todays code requirements Install PRV

Collect: $4,300.00

Confirmed with Madhur 805-791-5177 who will be on site 07/17, 1-4

Installation

Sales- Greg

Turn- Eric

4TON Upflow R802VA furnace, coil, SOV48 a/c, ducting 11 runs, CleanEffects

Total due - $25,858.00 *CHECK*

Sales-Kevin O.**Send Krista pic of water heater label or upload to acct**75-Gallon Gas Water Heater Replacement

Replacement of an existing 75-gallon gas water heater in a garage with no recirculation pump.

Location: Garage

Recirculation Pump: No

Tasks:

Preparation and Shutoff:

1. Shut off gas supply valve

2. Close main water supply

3. Drain existing water heater to empty tank

Removal of Existing Unit:

1. Disconnect gas line from heater

2. Detach cold and hot water supply lines

3. Remove and dispose of old unit per local regulations

New Water Heater Installation:

1. Position new 75-gallon unit with adequate clearance per code

2. Install new drain pan beneath unit

3. Connect new stainless steel water supply lines (cold and hot)

4. Install 1/4-turn ball valve on cold water inlet

5. Install expansion tank, adjusted to home water pressure (typically 50-60 PSI)

6. Fit new gas shutoff valve on gas line

7. Attach new flexible gas supply line with sediment trap

8. Secure unit with Unistrut mounting and earthquake straps

9. Reconnect to existing T&P relief valve exit point

10. Insulate water supply lines for efficiency

11. Install copper bonding wire from water lines to gas line for grounding

Venting and Combustion:

1. Install venting per manufacturer’s specs (e.g., double-wall or single-wall as required)

2. Secure single-wall vent connections with 3 screws each

3. Verify adequate combustion air supply per code

Testing and Startup:

1. Pressure-test gas and water connections for leaks

2. Fill tank and purge air from lines

3. Test T&P relief valve operation

4. Light pilot, set temperature to 120°F (or per client preference), and confirm burner ignition

5. Validate full operational status

Cleanup and Final Steps:

1. Clear debris from work area

2. Haul away old unit for disposal

3. Conduct final inspection with client walkthrough

Notes:

- Estimate valid for 30 days from issuance

- Permit fees, if required, are included as a separate line item

- Unforeseen issues or additional work will be quoted separately with client approval

- Exclusions: Drywall, paint, stucco, tile, concrete, stone repairs, or existing water damage

- Duration: 4-5 hours, 1 technician

- Warranty: Manufacturer - 6 years parts, 1 year labor.

- Qualifies for applicable utility rebates and federal tax credits (where available)

Descale RX Filter 1"

Install a 1-inch Descale RX filter system to treat hard water and prevent scale buildup in water heaters and plumbing systems, extending equipment lifespan and improving efficiency. The Descale RX filter uses a catalytic media (e.g., Template Assisted Crystallization) to transform dissolved calcium and magnesium into non-adhesive crystals that pass through the system without forming scale. This is critical for water heaters, as scale can reduce heating efficiency, increase energy costs, and lead to premature failure. The system requires no electricity, salt, or backwashing, making it low-maintenance and eco-friendly. Installation includes a bypass valve and shut-off valves for easy maintenance, ensuring reliable water quality for residential or commercial applications.

Location: Interior/Exterior (Near Water Heater or Main Water Line)

Tasks:

Preparation:

1. Locate optimal installation point on main water line or water heater inlet.

2. Shut off main water supply and drain affected piping section.

3. Set up work area with tools (pipe cutter, wrench, compression fittings, PPE) and drop cloths.

Filter Installation:

1. Install 1-inch Descale RX filter housing with catalytic media cartridge, per manufacturer specifications.

2. Connect filter to water line using copper or PEX piping with compression or threaded fittings.

3. Install bypass valve and shut-off valves for maintenance and filter replacement.

System Integration:

1. Secure filter housing to wall or floor with mounting brackets to prevent movement.

2. Ensure proper flow direction through filter (inlet/outlet per manufacturer markings).

3. Verify filter is accessible for future cartridge replacements (every 1-2 years).

Testing:

1. Restore water supply and check for leaks at all connections using a pressure test.

2. Run water through filter to verify flow rate and no restrictions.

3. Test water heater or fixtures to confirm normal operation post-installation.

Cleanup and Final Steps:

1. Clean work area and dispose of debris per local regulations.

2. Provide client with filter manual and maintenance schedule for cartridge replacement.

3. Conduct walkthrough to explain filter benefits and operation.

Notes:

- Prevents scale buildup in water heaters, improving efficiency and lifespan.

- Additional piping or relocation quoted separately if needed.

- Advise client to replace filter cartridge every 1-2 years, depending on water hardness.

- Estimate valid for 30 days from issuance

- Permit fees, if required, are included as a separate line item

- Unforeseen issues or additional work will be quoted separately with client approval

- Exclusions: Drywall, paint, stucco, tile, concrete, stone repairs, or existing water damage

- Warranty: 5 years parts, 2 years labor

CC or Check $5000.00

Installation **7AM START

Sales- Greg

Turn- Nathan3TON upflow S8V2 furnace, Honeywell #T6

Total due - $9,200.00 (CC)

Install ***NOTE; THIS IS ON MATT AS A PLACE HOLDER; GREG FLACK WILL BE PERFORMING THIS INSTALLATION.

Sales- Owen

Turn- N/A

200a panel upgrade

Total due - $6,300.00 (CC OR CHECK)

Per Owen

There are a total of 6 detectors we will be replacing for new 10 year battery backup combo detectors. The existing wiring will be kept the same, all of the new 6 smoke/carbon detectors will be interlinked.

We will also be replacing an old duplex outlet that had a loose connection.

Customer is H/O

Not Gated

Amount to collect: $1096

Please call when you're on the way (805) 701-9134 Barbara