Take a look at our past work!

Installation

Sales- Chip

Turn- Nathan

4TON horizontal SL280V (in shop), NUVE thermostat

Total due - $9,150.00 (CHECK)

Sales-TracyPlease take picture of water heater and send a pic to Krista or upload to pics in jobCX WILL BE HOME AROUND 9AM

-Water heaterDrain and remove the old water heater.Install a new 40 gallon electric water heater.

Install a new drain pan.

Add water heater stand 

Re use electric connector, new water connectors, supply ball valve shut-off and quake strap.Install expansion tank at supply line of water.

Hook T&P valve up to existing copper line.

Tax and permits are included in the price of cost.

6 year tank 6 year parts and 1 year labor warranty - 40 Gal Kit - Bradford Water Heater 40 Gal

-Comfort pumpInstalled comfort pump at furthest fixline with proper mix it valve at cold water side. 

-Flagship 1054Install a Flagship whole-house water filtration system. Flushed the excess carbon from the unit and bleed the air out of the system

CC or check $7561.00

Installation of 50-gallon Gas Water Heater w/ comfort pump

Sold by Derek

Replacement of an existing 50-gallon gas water heater in a garage with no recirculation pump.

Location: Garage

Recirculation Pump: No

Tasks:

Preparation and Shutoff:

1. Shut off gas supply valve

2. Close main water supply

3. Drain existing water heater to empty tank

Removal of Existing Unit:

1. Disconnect gas line from heater

2. Detach cold and hot water supply lines

3. Remove and dispose of old unit per local regulations

New Water Heater Installation:

1. Position new 50-gallon unit with adequate clearance per code

2. Install new drain pan beneath unit

3. Connect new stainless steel water supply lines (cold and hot)

4. Install 1/4-turn ball valve on cold water inlet

5. Install expansion tank, adjusted to home water pressure (typically 50-60 PSI)

6. Fit new gas shutoff valve on gas line

7. Attach new flexible gas supply line with sediment trap

8. Secure unit with Unistrut mounting and earthquake straps

9. Reconnect to existing T&P relief valve exit point

10. Insulate water supply lines for efficiency

11. Install copper bonding wire from water lines to gas line for grounding

12. Cover base/stand with sheet metal for protection

Venting and Combustion:

1. Install venting per manufacturer’s specs (e.g., double-wall or single-wall as required)

2. Secure single-wall vent connections with 3 screws each

3. Verify adequate combustion air supply per code

Testing and Startup:

1. Pressure-test gas and water connections for leaks

2. Fill tank and purge air from lines

3. Test T&P relief valve operation

4. Light pilot, set temperature to 120°F (or per client preference), and confirm burner ignition

5. Validate full operational status

Cleanup and Final Steps:

1. Clear debris from work area

2. Haul away old unit for disposal

3. Conduct final inspection with client walkthrough

Comfort Pump

Cost to install a comfort series pump on the tanked water heater to reduce the time that it takes for hot water to be delivered to the master bathroom. Will install bypass valve under the furthers master lavatory sink.

This is not for tankless.

Notes:

- Estimate valid for 60 days from issuance

- Includes permit fees (if required)

- Unforeseen issues or additional work will be quoted separately with client approval

- Exclusions: Drywall, paint, stucco, tile, concrete, stone repairs, or existing water damage

- Duration: 1-2 hours, 1 technician

- Warranty: 3 years parts and labor

- Financing: 18 months at 0% interest available

Amount to collect when done: $4,497.00

Please call (805) 216-2887Laurie

No permit neededJB delivering materials 10/06 10:00 am